Your shopping cart is empty!
MAX7219 Dot Matrix Module DIY Kit SCM Control Module For Arduino MAX7219 Dot Matrix Display Module SCM Control Module For Arduino Descriptions : The MAX7219 is an integrated serial input / output common-cathode display driver, it is connected to a microprocessor with 8digit 7segment digital LED display can also be connected to the bar graph display or 64 separate LED. On B BCD encoder including an on chip, multi channel scanning loop word drive, but also an 8 x 8 static RAM is used to s..
Membrane Type Keypad - 12 Key - 4x3 Matrix 4 x 3 Matrix Membrane Keypad 7 pin connector Adhesive mounting Maximum Circuit Rating: 35VDC, 100mA Insulation Resistance: 100M Omh, 100V Dielectric Withstand: 250VRms (50-60Hz, 1min) Contact Bounce: <=5ms Life Expectancy: 1 million closures Operation Temperature: 0 to +70 centigrade Humidity: 40 centigrade, 90%-95%, 240 hours ..
Microusb +5V 18650 Lithium Battery 1A Charging Module with TP4056 Protection Current- 1A adjustable. Charge precision- 1.5%. Input voltage- 4.5V-5.5V. Full charge voltage- 4.2V Led indicator- red is charging Green is full charged. Input interface- micro USB. Work temperature- -10 cto +85 c. Inversed polarity- NO. NOTE: 1. Ampere meter can only be connected to 5v input end of the module. 2. It is better that the charging current is 37% of the battery capacity. If you charge to the battery of 1000mAH, current of 400 is enough The connection wire should not be too thick. 4. Make sure the connect point is good. 5. If the input voltage is too high, like 5.2v, the current will be less than 1000mA, it is normal. It is protection function, auto-substract the charging current to avoid burn damage to chip NO Reversal polarity ..
Mobile Controlled Home Automation (On/Off Lights/Fans with Mobile) Controlling a home appliances wirelessly is possible with several methods such as Remote, Bluetooth, Wi-Fi, etc. But, the controls of these communication methods are limited to certain areas, and complicated to design as well. To overcome these difficulties, we have come up with a Mobile Controlle Home Automation (On/Off Lights/Fans with Mobile) (DTMF Based) Home Automation (On/Off Lights/Fans with Mobile) is a mobile device, which provides wide-range of wireless control ability to your home appliances unless your cell phone gets out of signal. A general concept of Home Automation (On/Off Lights/Fans with Mobile) (DTMF Based) is that it can be controlled from any part of the world with just an inclusion of a camera. In this project the home appliances like fan, lights etc, is controlled by a mobile phone that makes call to the mobile phone attached to the device in the course of the ..
Mobile Controlled Home Automation Without Microcontroller (On/Off Lights/Fans with Mobile) Controlling a home appliances wirelessly is possible with several methods such as Remote, Bluetooth, Wi-Fi, etc. But, the controls of these communication methods are limited to certain areas, and complicated to design as well. To overcome these difficulties, we have come up with a Mobile Control Home Automation Without Microcontroller (On/Off Lights/Fans with Mobile) (DTMF Based) Home Automation Without Microcontroller (On/Off Lights/Fans with Mobile) is a mobile device, which provides wide-range of wireless control ability to your home appliances unless your cell phone gets out of signal. A general concept of Home Automation Without Microcontroller (On/Off Lights/Fans with Mobile) (DTMF Based) is that it can be controlled from any part of the world with just an inclusion of a camera. In this project the home appli..
Modulated 38Khz IR Sensor for Obstacle Line Arduino Rasp Pi 8051 AVR This is a multipurpose Modulated infrared sensor which can be used for obstacle sensing, color detection (between basic contrasting colors), line sensing, etc and also as an encoder sensor. The sensor provides a digital ouput. The sensor outputs a logic one(+5V) at the digital output when an object is placed in front of the sensor and a logic zero(0V), when there is no object in front of the sensor. An onboard LED is used to indicate the presence of an object. This digital output can be directly connected to an Arduino, Raspberry Pi, AVR, PIC, 8051 or any other microcontroller to read the sensor output. This Modulated 38Khz IR sensors is very less susceptible to ambient light and the IR sensor on this sensor is suitably covered to reduce effect of ambient light on the sensor. For maximum, range the onboard potentiometer should be used to calibrate the sensor. To set the potentiometer, use a..
DC MOTOR / STEPPER MOTOR DRIVER BOARD with L293D IC for ARM ARDUINO AVR PIC 8051 (L293D Board With IC,Compatible with all Microcontroller) &..
Nipper-07 Copper And Aluminium Wire Cutter The Nipper-07 Copper And Aluminium Wire Cutter feature forged steel construction for durability, It is only used for Cutting Copper And Aluminium Wires. Nipper-07 Copper And Aluminium Wire Cutter Material: Iron It is only used for Cutting Copper And Aluminium Wires. Package Included: 1 x Nipper-07 Copper And Aluminium Wire Cutter Safety/Care Instructions: Keep the product out of reach of children ..
PIC 40PIN Development Board (with MAX232 IC's ) With this board you can develop and prototype with PIC (40 pin) microcontrollers. The RS232 driver on board allows easy connection with PC or other embedded hardware. The board have User buttons and status LEDs. The bridge rectifire allow this board to be powered with both AC and DC power supply adapters. FEATURES 1. PIC Development Board for Microchip any 40 PIN PIC Series like. 16FXXX, 18FXXX (EX. 16F877A - 40 PIN). 2. ICSP Socket for Programming through PICKIT2 or PICKIT3 3. On board Regulated Power Supply 5v,12v supplies 4. Easy to test with Burg Connecters wires 5. An RS232 Serial Port 6. 7 Segment Multiplexed Display 7. DC Power Supply Connector(12v Ac or Dc) 8. READY INTERFACE For LCD display 2linex16Character 9. 24Cxx (I2C) (EEPROM) 10. RTC (DS1307) 11. 4 LED array 12. Matrix Key Pad 13. 4 Interrupt Switches 14. ADC Interface Support 15. ULN2008 Support For Interfacing Stepper Motors. Package Conten..
PIC 40PIN Development Board Mini (with MAX232 IC's ) With this board you can develop and prototype with PIC (40 pin) microcontrollers. The RS232 driver on board allows easy connection with PC or other embedded hardware. The board have User buttons and status LEDs. The bridge rectifier allow this board to be powered with both AC and DC power supply adapters. FEATURES 1. PIC Development Board for Microchip any 40 PIN PIC Series like. 16FXXX, 18FXXX (EX. 16F877A - 40 PIN). 2. ICSP Socket for Programming through PICKIT2 or PICKIT3 3. On board Regulated Power Supply 5v,12v supplies 4. Easy to test with Burg Connecters wires 5. An RS232 Serial Port 6. DC Power Supply Connector (12v Ac or Dc) 7. 4 LED array 8. 2 Interrupt Switches Package Content 1. PIC Development Board Mini for Microchip any 40 PIN PIC Series like. 16FXXX, 18FXXX (EX. 16F877A - 40 PIN). ..
PIC 40PIN Development Board Mini with 16F877A , Max232 and PROGRAMMER With this board you can develop and prototype with PIC (40 pin) microcontrollers. The RS232 driver on board allows easy connection with PC or other embedded hardware. The board have User buttons and status LEDs. The bridge rectifier allow this board to be powered with both AC and DC power supply adapters. FEATURES 1. PIC Development Board for Microchip any 40 PIN PIC Seies like. 16FXXX, 18FXXX (EX. 16F877A - 40 PIN). 2. ICSP Socket for Programming through PICKIT2 or PICKIT3 3. On board Regulated Power Supply 5v,12v supplies 4. Easy to test with Burg Connecters wires 5. An RS232 Serial Port 6. DC Power Supply Connector (12v Ac or Dc) 7. 4 LED array 8. 2 Interrupt Switches PIC PROGRAMMER Features Flash Burner for PIC Series +5 Volt PIC Microcontrollers. Communication - USB Auto Erase before writing and Auto Verify after writing Programming Socket USB Powered ..
PIC 40PIN Development Board Mini with 16F877A and Max232 IC With this board you can develop and prototype with PIC (40 pin) microcontrollers. The RS232 driver on board allows easy connection with PC or other embedded hardware. The board have User buttons and status LEDs. The bridge rectifier allow this board to be powered with both AC and DC power supply adapters. FEATURES 1. PIC Development Board for Microchip any 40 PIN PIC Seies like. 16FXXX, 18FXXX (EX. 16F877A - 40 PIN). 2. ICSP Socket for Programming through PICKIT2 or PICKIT3 3. On board Regulated Power Supply 5v,12v supplies 4. Easy to test with Burg Connecters wires 5. An RS232 Serial Port 6. DC Power Supply Connector (12v Ac or Dc) 7. 4 LED array 8. 2 Interrupt Switches Package Content 1. PIC 40PIN Development Board Mini with 16F877A and Max232 IC..
PIC 40PIN Development Board with 16F877A, MAX232 , RTC , AT24C32, ULN2003 IC With this board you can develop and prototype with PIC (40 pin) microcontrollers. The RS232 driver on board allows easy connection with PC or other embedded hardware. The board have User buttons and status LEDs. The bridge rectifire allow this board to be powered with both AC and DC power supply adapters. FEATURES 1. PIC Development Board for Microchip any 40 PIN PIC Seies like. 16FXXX, 18FXXX (EX. 16F877A - 40 PIN) 2. ICSP Socket for Programming through PICKIT2 or PICKIT3 3. On board Regulated Power Supply 5v,12v supplies 4. Easy to test with Burg Connecters wires 5. An RS232 Serial Port 6. 7 Segment Multiplexed Display 7. DC Power Supply Connector(12v Ac or Dc) 8. READY INTERFACE For LCD display 2linex16Character 9. 24Cxx (I2C) (EEPROM) 10. RTC (DS1307) 11. 4 LED array 12. Matrix Key Pad 13. 4 Interrupt Switches 14. ADC Interface Support 15. ULN2008 Support For Interfacing Stepper Moto..
PIC 40PIN Development Board with 16F877A, MAX232 , RTC , AT24C32, ULN2003 IC & PROGRAMMER With this board you can develop and prototype with PIC (40 pin) microcontrollers. The RS232 driver on board allows easy connection with PC or other embedded hardware. The board have User buttons and status LEDs. The bridge rectifire allow this board to be powered with both AC and DC power supply adapters. FEATURES 1. PIC Development Board for Microchip any 40 PIN PIC Seies like. 16FXXX, 18FXXX (EX. 16F877A - 40 PIN) 2. ICSP Socket for Programming through PICKIT2 or PICKIT3 3. On board Regulated Power Supply 5v,12v supplies 4. Easy to test with Burg Connecters wires 5. An RS232 Serial Port 6. 7 Segment Multiplexed Display 7. DC Power Supply Connector(12v Ac or Dc) 8. READY INTERFACE For LCD display 2linex16Character 9. 24Cxx (I2C) (EEPROM) 10. RTC (DS1307) 11. 4 LED array 12. Matrix Key Pad 13. 4 Interrupt Switches 14. ADC Interface Support 15. ULN2008 Support For Interfa..
PIC 40PIN Development Board with 16F877A, MAX232 , RTC , AT24C32, ULN2003 IC , LCD & PROGRAMMER With this board you can develop and prototype with PIC (40 pin) microcontrollers. The RS232 driver on board allows easy connection with PC or other embedded hardware. The board have User buttons and status LEDs. The bridge rectifire allow this board to be powered with both AC and DC power supply adapters. FEATURES 1. PIC Development Board for Microchip any 40 PIN PIC Seies like. 16FXXX, 18FXXX (EX. 16F877A - 40 PIN) 2. ICSP Socket for Programming through PICKIT2 or PICKIT3 3. On board Regulated Power Supply 5v,12v supplies 4. Easy to test with Burg Connecters wires 5. An RS232 Serial Port 6. 7 Segment Multiplexed Display 7. DC Power Supply Connector(12v Ac or Dc) 8. READY INTERFACE For LCD display 2linex16Character 9. 24Cxx (I2C) (EEPROM) 10. RTC (DS1307) 11. 4 LED array 12. Matrix Key Pad 13. 4 Interrupt Switches 14. ADC Interface Support 15. ULN2008 Support For I..
PIC 40PIN Development Board with MAX232 , RTC , AT24C32, ULN2003 IC's With this board you can develop and prototype with PIC (40 pin) microcontrollers. The RS232 driver on board allows easy connection with PC or other embedded hardware. The board have User buttons and status LEDs. The bridge rectifire allow this board to be powered with both AC and DC power supply adapters. FEATURES 1. PIC Development Board for Microchip any 40 PIN PIC Seies like. 16FXXX, 18FXXX (EX. 16F877A - 40 PIN) 2. ICSP Socket for Programming through PICKIT2 or PICKIT3 3. On board Regulated Power Supply 5v,12v supplies 4. Easy to test with Burg Connecters wires 5. An RS232 Serial Port 6. 7 Segment Multiplexed Display 7. DC Power Supply Connector(12v Ac or Dc) 8. READY INTERFACE For LCD display 2linex16Character 9. 24Cxx (I2C) (EEPROM) 10. RTC (DS1307) 11. 4 LED array 12. Matrix Key Pad 13. 4 Interrupt Switches 14. ADC Interface Support 15. ULN2008 Support For Interfacing Stepper Motors. ..
PICKIT2 programmer for +5 Volt PIC Series Microcontrollers Features Flash Burner for PIC Series +5 Volt PIC Microcontrollers. Communication - USB Auto Erase before writing and Auto Verify after writing Programming Socket USB Powered Device Support : Supports all PIC12, PIC16 and PIC18 +5 volt PIC Microcontroller. Package Content PICKIT2 programmer for +5 Volt PIC Series Microcontrollers Free USB Port Cable Free 6 Burg Cable Female 2 Female..
PIR Motion Sensor Detector Module HC-SR501 8051 ARDUINO PIC ATMEL AVR RASPBERRY ETC BEST FOR OCCUPANCY APPLICATIONS, BEST QUALITY GAURANTED Package Contents 1 x HC-SR501 PIR Motion Sensor (Detector) Module Product Details Compatible with ARDUINO, RASPBERRY PI, AVR , PIC, 8051, etc. The PIR Sensor module allows you to sense motion. It is almost always used to detect the motion of a human body within the sensor's range. It is often referred to used "PIR", "Pyroelectric", "Passive Infrared" and "IR Motion" sensor. The module has an on-board pyroelectric sensor, conditioning circuitry and a dome shaped Fresnel lens. 100% Brand New and High Qu..
Features: INPUT VOLTAGE 12V AC/DC OUTPUT VOLTAGE 12V DC and 5V DC OverVoltage and Under voltage protection In Line Noise Filter Short Circuit Protection Best Quality PCB Material Regulator based output. 8 pin/berg Connector for each +12v dc, +5v dc and GND. DC jack for connecting adaptor directly. Can Run 24*7 Without any Problem..